ReactionBench logoReactionBenchREACTION TIME BENCHMARKS
Home/Guides/Ruler Drop Test Experiment: Method, Worksheet and Worked Example

Ruler Drop Test Experiment: Method, Worksheet and Worked Example

The ruler drop test experiment measures reaction time with a ruler, a partner and a table of results. One person drops the ruler without warning, the other catches it, and the distance the ruler fell converts to a time with t = √(2d / g). This guide is the classroom method: the aim, the equipment, the steps, the variables that make it a fair test, a blank results table, a worked example and the errors that spoil results. It suits KS3, GCSE and US middle school science. To turn your centimetres into milliseconds, use the ruler drop test chart. No ruler at hand? Take the online ruler drop test.

Tajammal Maqbool
Tajammal Maqbool
20 November 2026 · 6 min read
Pupils' hands writing in notebooks at a wooden desk, with a wooden ruler, an eraser and pens beside them.
A wooden ruler, a partner and a results table are all the equipment you need. The distance the ruler falls before it is caught converts to a reaction time.
The aim

Aim and the physics behind the experiment

Aim: to measure how long a person takes to react to a falling ruler, and to test whether one factor, such as the hand used, changes that time.

The ruler is in free fall once it is released, so the distance it drops depends only on time. The standard equation for a body released from rest is d = ½ g t². Rearranged for time, it gives t = √(2d / g), where d is the catch distance in metres and g is the acceleration due to gravity. The standard value of g is 9.806 65 m/s² (NIST), and this guide rounds it to 9.81 m/s².

The distance is the only thing you read from the ruler. The catcher's reaction time is the time the ruler needed to fall that far. A longer fall means a slower reaction.

Before you start

Equipment and safety

You need a 30 cm ruler, two people (a dropper and a catcher), a results table and a pencil. The National Physical Laboratory (NPL) uses this same set-up in its measurement-at-home activity. A plastic ruler is a good choice, because it is light.

Safety is simple. Keep feet clear of the drop zone, because NPL advises against dropping the ruler onto people's feet.

The method

Ruler drop test method, step by step

These steps follow the NPL protocol.

1. Set up the catcher. The catcher extends the forearm at elbow height, with the thumb and forefinger about 1 cm apart. The dropper holds the ruler so that the 0 cm mark sits between those fingers.

2. Signal ready. The catcher says when they are ready. The dropper then counts silently to a number between 3 and 5, and changes that number every time. This stops the catcher guessing the moment of release.

3. Drop and catch. The dropper lets go without any other warning. The catcher pinches the ruler as fast as possible.

4. Read the mark. Record the centimetre mark nearest the pinch point. That number is the catch distance.

5. Repeat. NPL repeats each trial five times and takes the average. Ignore any drop where the catcher fails to catch the ruler. Then swap roles so that both partners collect data.

A published validation study used a stricter version. Participants sat with the elbow bent at 90 degrees and resting on a table. The examiner held a 60 cm ruler with its zero mark level with the top of the thumb and index finger, and dropped it five times after the word "ready", at intervals of 3, 4, 6, 2 and 4 seconds. A ruler that reached the floor was recorded as 61 cm.

Variables

Fair test: variables to control and change

A fair test changes one thing and keeps everything else the same. Pick one independent variable per experiment, then use the table to decide what to hold constant.

The most common investigation compares the dominant hand with the non-dominant hand. NPL defines the dominant hand as the one that more comfortably holds a spoon or a pencil. Test each hand with the same number of drops, and label every result "dominant" or "non dominant".

A second investigation compares a sight cue with a sound cue. In the sound version the catcher closes their eyes and the dropper says "now" as they release. This guide does not predict which will be faster, because the point of the experiment is to find out. Your results show only what happened in your class.

InvestigationIndependent variableKeep the same
Hand comparisonDominant or non-dominant handRuler, drop height, same catcher, same cue, same number of drops
Cue comparisonSight cue or sound cueSame hand, same ruler, same catcher, same number of drops
DistractionCounting backwards or notSame hand, same cue, same ruler, same catcher
Fair-test planner. Change only the variable in the second column and keep the third column the same for every trial.
The worksheet

Ruler drop test results table

Copy the table below onto paper, or print this page. Record the catch distance in centimetres for each drop. Then convert it to milliseconds with the ruler drop test chart or with the formula. Take the mean (the average) for each hand, as NPL does. Top End Sports recommends at least five trials with about 30 seconds of rest between them.

To convert a distance, divide it by 100 to get metres, then apply t = √(2d / g). For a quick look-up, use the chart instead. The chart uses the same formula and the same value of g.

TrialDominant hand (cm)Dominant hand (ms)Non-dominant hand (cm)Non-dominant hand (ms)
1
2
3
4
5
Mean
Blank ruler drop test results table. Write distances in cm and times in ms. Leave a failed catch blank and do not count it.
Worked example

Worked example: from centimetres to milliseconds

A student catches the ruler at 15 cm. Convert to metres: d = 0.15 m. Then t = √(2 × 0.15 / 9.81) = √0.03058 ≈ 0.175 s, which is 175 ms.

The table shows the same calculation for three catch distances. These are arithmetic results from the formula with g = 9.81 m/s², not measurements, and they match the values in the ruler drop test chart.

Now take a set of drops. A catcher records 14, 16, 15, 18 and 17 cm. The mean distance is 16 cm, which gives about 181 ms from the same formula. Write down whether you averaged the distances or the times, so that your class uses one method.

Catch distanceIn metresCalculationReaction time
10 cm0.10 m√(2 × 0.10 / 9.81)143 ms
15 cm0.15 m√(2 × 0.15 / 9.81)175 ms
20 cm0.20 m√(2 × 0.20 / 9.81)202 ms
Computed from t = √(2d / g) with g = 9.81 m/s². These are calculated values, not measured results.
Evaluating the experiment

Sources of error and how to reduce them

Anticipation. If the catcher can predict the drop, the experiment measures guessing and not reaction. Vary the silent count each time, as NPL does, and give no other cue. Top End Sports gives the same rule: no anticipation or guessing.

Reading the mark. Read the ruler at the same point on the thumb every time. A reading error of one centimetre changes the calculated time by several milliseconds.

Too few trials. One drop is noisy. In a validation study of the ruler drop test, the test-retest reliability (ICC) of the simple version was 0.57. That is one reason to take several trials.

Practice. NPL notes that practice may reduce reaction time. Give every student the same number of warm-up drops, because the hand tested second may otherwise benefit from practice.

Other conditions. NPL lists background noise, time of day and diet as possible influences. Test in the same room and at about the same time.

If the ruler is too short for slow catches, use a longer stick or switch to the online ruler drop test, which uses the same physics.

Stop reading, start testing
Where do you actually land?

A number you measured beats a number you read. Take the test and get your own median in about thirty seconds.

Take the test
Questions
What is the aim of the ruler drop test experiment?
The aim is to measure reaction time using a falling ruler, and then to test one variable, such as the dominant hand against the non-dominant hand. The catch distance is read from the ruler and converted to time with t = √(2d / g).
How do you convert ruler drop distance to reaction time?
Divide the catch distance in centimetres by 100 to get metres, then apply t = √(2d / g) with g = 9.81 m/s². A 15 cm catch gives about 175 ms. For a quick look-up, use the ruler drop test chart.
How many trials should students do?
NPL repeats each trial five times and takes the average. Top End Sports recommends at least five trials with about 30 seconds of rest between them. Ignore any drop where the ruler is not caught.
What are the variables in the ruler drop test?
The independent variable is the one thing you change, for example dominant or non-dominant hand. The dependent variable is the catch distance, converted to time. Control variables include the ruler, the catcher, the number of drops and the cue.
Why do my results change from one drop to the next?
A single drop is noisy. A validation study of the ruler drop test found a test-retest reliability (ICC) of 0.57 for the simple version, so take several drops and use the mean. Anticipation and misreading the ruler also add variation.
Can I do the experiment without a ruler?
Yes. The online ruler drop test runs the same physics on screen, so a student can repeat the experiment on a device and compare it with the classroom result.
Sources
  1. 01National Physical Laboratory. Measurement at home: Reaction time (30 cm ruler method, five repeats, dominant and non-dominant hand). National Physical Laboratory. Measurement at home: Reaction time (30 cm ruler method, five repeats, dominant and non-dominant hand).
  2. 02Ferreira, S., Raimundo, A., del Pozo-Cruz, J., Leite, N., Pinto, A., & Marmeleira, J. (2024). Validity and reliability of a ruler drop test to measure dual-task reaction time, choice reaction time and discrimination reaction time. Aging Clinical and Experimental Research, 36(1), 61. Ferreira, S., Raimundo, A., del Pozo-Cruz, J., Leite, N., Pinto, A., & Marmeleira, J. (2024). Validity and reliability of a ruler drop test to measure dual-task reaction time, choice reaction time and discrimination reaction time. Aging Clinical and Experimental Research, 36(1), 61.
  3. 03Top End Sports. Reaction Time Calculator: Ruler Drop Test & Athletic Performance (formula t = sqrt(2d/g), trial counts). Top End Sports. Reaction Time Calculator: Ruler Drop Test & Athletic Performance (formula t = sqrt(2d/g), trial counts).
  4. 04NIST. Standard acceleration of gravity, g_n = 9.806 65 m/s² (CODATA 2022). NIST. Standard acceleration of gravity, g_n = 9.806 65 m/s² (CODATA 2022).
Put it into practice